Expert Answers

(Solved): Create the free-body diagram for particle 1. Use the checkbo...

Create the free-body diagram for particle 1.
Use the checkboxes to select the correct vectors as instructed above. Move the vectors
to the correct starting points and orient them in the correct direction as instructed.
F_(1)
F_(2)
F_(3)
Key to Force Labels
F_(1)= Force from particle 1
F_(2)= Force from particle 2
F_(3)= Force from particle 3
Point the acceleration vector
in the correct direction

$5

Buy Answer

(Solved): A web application suffers from frequent security incidents. ...

A web application suffers from frequent security incidents. The technical team decides to implement testing to identify potential weaknesses. Which penetration testing should they perform to assess the application while running? Static Application Security Testing (SAST) Mobile Application Testing Dynamic Application Security Testing (DAST) Interactive Application Security Testing (IAST)

$5

Buy Answer

(Solved): A polystyrene rod of length 12 in. and diameter 0.5 in. is s...

A polystyrene rod of length 12 in. and diameter 0.5 in. is subjected to an 800-lb tensile load. Knowing that E = 0.45×10 6 psi, determine (a) the elongation of the rod, (b) the normal stress in the rod.

$5

Buy Answer

(Solved): ! Required information A 90\deg elbow in a horizontal pipe ...

!

Required information A

90\deg

elbow in a horizontal pipe is used to direct water flow upward at a rate

m

35k(g)/(s)

. The diameter of the entire elbow is 10 cm . The elbow discharges waterr into the atmosphere, and thus the pressure at the exit is the local atmospheric pressure. The elevation difference between the centers of the exit and the inlet of the elbow is 50 cm . The weight of the elbow and the water in it is considered to be negligible. Take the density of water to be

1000k(g)/(m^(3))

and the momentum-flux correction factor to be 1.03 at both the inlet and the outlet. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. Determine the anchoring force needed to hold the elbow in place. The anchoring force needed to hold the elbow in place is

◻

N The resultant direction of the force is

◻

$5

Buy Answer

(Solved): The shaft is supported at its ends by two bearings A and B a...

The shaft is supported at its ends by two bearings A and B and
is subjected to the forces applied to the pulleys fixed to the shaft.
(Figure 1) The T_(1)=590-N forces act in the -z direction and the
200-N and 80-N forces act in the +y direction. The journal
bearings at A and B exert only y and z components of force on
the shaft. Part A
Determine the resultant normal force on the cross section at C.
Express your answer to three significant figures and include appropriate units.
Previous Answers
Part B
Determine the resultant shear force in the y direction on the cross section at C.
Express your answer to three significant figures and include appropriate units.
(V_(C))_(y)=
Previous Answers Request Answer
Incorrect; Try Again; 5 attempts remaining Part C
Determine the resultant shear force in the z direction on the cross section at C.
Express your answer to three significant figures and include appropriate units.
(V_(C))_(z)=
Previous Answers Request Answer
Incorrect; Try Again; 5 attempts remaining
Part D
Determine the resultant torque on the cross section at C.
Express your answer to three significant figures and include appropriate units.
T=Part E
Determine the resultant bending moment in the y direction on the cross section at C.
Express your answer to three significant figures and include appropriate units.
(M_(C))_(y)=
Request Answer
Part F
Determine the resultant bending moment in the z direction on the cross section at C.
Express your answer to three significant figures and include appropriate units.
(M_(C))_(z)=

$5

Buy Answer

(Solved): olve the system using matrices (row operations) 4x4y5z3x+2y...

olve the system using matrices (row operations) ⎧⎩⎨⎪⎪4x−4y−5z3x+2y+6z3x+5y+4z=6=24=20{4x−4y−5z=63x+2y+6z=243x+5y+4z=20 How many solutions are there to this system? A. None B. Exactly 1 C. Exactly 2 D. Exactly 3 E. Infinitely many F. None of the above If there is one solution, give its coordinates in the answer spaces below. If there are infinitely many solutions, enter z in the answer blank for zz, enter a formula for yy in terms of zz in the answer blank for yy and enter a formula for xx in terms of zz in the answer blank for xx. If there are no solutions, leave the answer blanks for xx, yy and zz empty. x=x= y=y= z=z= Note: In order to get credit for this problem all answers must be correct. You have attempted this problem 7 times. Your overall recorded score is 0%. You have 3 attempts remaining.

$5

Buy Answer

(Solved): (e) \lim_((x,y,z)->(0,0,0))(x^(2)y^(2)z^(2))/(x^(2) y^(2)...

(e)

\lim_((x,y,z)->(0,0,0))(x^(2)y^(2)z^(2))/(x^(2) y^(2) z^(2))

$5

Buy Answer

(Solved): 1.) A personal union is a) a dynastic marriage b) an oath ...

1.) A “personal union” is a) a dynastic marriage b) an oath of fealty to a prince c) the promise of the monarch to be guided by his conscience and by God d) a constitutional arrangement by which the same prince governs two or more territories, each through its own laws and institutions e) the acceptance by certain eastern-rite churches of the pope as their spiritual superior

$5

Buy Answer

(Solved): when is not true about a neurons' resting membrane poten...

when is not true about a neurons' resting membrane potential? it is typically between -40 and -90 mV ion pumps help to maintain it at rest there are more sodium ions inside the cell and more potassium outside the cell the potential is close to the equilibrium potential of potassium all of the above are true

$5

Buy Answer

(Solved): What minimum horizontal force must the monkey apply to keep ...

What minimum horizontal force must the monkey apply to keep the box moving at constant velocity once it has been started?